Yes, earlier than mid Qing is really hard, other than some export Kangxi wares which are fairly recognizable. Mid Qing already is a quite a bit more expensive than late Qing - especially if one is looking for a pot with good craftsmanship. Late Qing/ROC is a very nice period in terms of price/rewardBok wrote: ↑Sat Feb 02, 2019 11:23 pmYes that is as well as far as I will go on my Yixing journey! Anything older becomes a serious risk in investment. The same expert also told me that he considers older than mid Qing too risky and nebulous, almost impossible to verify, yet the prices are enormous.
Yixing
- tingjunkie
- Posts: 100
- Joined: Tue Apr 17, 2018 7:39 pm
Nice one! Deserves some proper kintsugi repair.
For now not enough damage yet, just a tiny chip.
Due to the bad influence of certain people I got my first Zhuni teapot... opportunity arose, price was pretty good, so I had no good excuse other than owning too many pots! For the sake of science I needed a Zhuni pot to compare with other clays, ähem...
It does not seem to be a pure Zhuni, too reddish for that and some tiny grains of other clay seem to be blended in. Some have suggested it might be a blend with high quality hongni. Other factors indicate it is a 90s pot. Clay, whatever it is, seems very good quality, workmanship is excellent.
From first use it performs as I would have expected a Zhuni to perform. Gathering a lovely shine very quickly and it sings when poured over with boiling water, if you know what I mean.
It does not seem to be a pure Zhuni, too reddish for that and some tiny grains of other clay seem to be blended in. Some have suggested it might be a blend with high quality hongni. Other factors indicate it is a 90s pot. Clay, whatever it is, seems very good quality, workmanship is excellent.
From first use it performs as I would have expected a Zhuni to perform. Gathering a lovely shine very quickly and it sings when poured over with boiling water, if you know what I mean.
- Attachments
-
- 6176844E-E0A2-4824-8562-DC398D3F798A.jpeg (166.69 KiB) Viewed 8600 times
Nice pot! The clay looks pretty good quality. I am not sure if it's zhuni or hongni, but it should brew well.Bok wrote: ↑Mon Feb 04, 2019 12:23 amDue to the bad influence of certain people I got my first Zhuni teapot... opportunity arose, price was pretty good, so I had no good excuse other than owning too many pots! For the sake of science I needed a Zhuni pot to compare with other clays, ähem...
It does not seem to be a pure Zhuni, too reddish for that and some tiny grains of other clay seem to be blended in. Some have suggested it might be a blend with high quality hongni. Other factors indicate it is a 90s pot. Clay, whatever it is, seems very good quality, workmanship is excellent.
From first use it performs as I would have expected a Zhuni to perform. Gathering a lovely shine very quickly and it sings when poured over with boiling water, if you know what I mean.
-
- Posts: 429
- Joined: Sun Dec 16, 2018 5:19 am
- Location: Seattle, USA
What do y'all do for single hole pots? I'm having trouble with the hongni that I got a while back, I can't use it without the tea getting stuck in the hole. Is there some really easy solution that I don't know about?
Practice makes perfect, difficult to explain how, but once you know your pot and your leaves it rarely gets stuck.swordofmytriumph wrote: ↑Tue Feb 05, 2019 1:58 amWhat do y'all do for single hole pots? I'm having trouble with the hongni that I got a while back, I can't use it without the tea getting stuck in the hole. Is there some really easy solution that I don't know about?
A lot depends on how you pour the first round and how you place the leaves, how much time you give them before the first pour etc.
Don’t want to derail the thread too much here: just experiment with how fast or slow in this case you tilt the pot when pouring, take it slow for the first infusion, once the leaves are opened up they will pretty much stay in place, unless you under-load the pot with too little leaf. After the first brew I sometimes use a tool to push the leaves a bit away from the exit hole, afterwards that is usually not necessary anymore.
Goes without saying that Sencha is not ideal for this kind of pot
-
- Posts: 429
- Joined: Sun Dec 16, 2018 5:19 am
- Location: Seattle, USA
This is so cool! Thank you soooo much this is gonna solve everything!
Also thanks for the tips @Bok
Last edited by swordofmytriumph on Tue Feb 05, 2019 4:36 am, edited 1 time in total.
-
- Posts: 429
- Joined: Sun Dec 16, 2018 5:19 am
- Location: Seattle, USA
Thanks! I just got one of each!